#Make your own record player shelf how to#

And though it may save space, never stack your records horizontally or flat - the added, crushing weight can warp, bend, or break them. As a reference, 100 records can weigh almost 40 pounds.

Weight: A stack of records is a heavy load, so check to see the weight capacity of how much the shelf you’re eyeing can hold. If that’s a concern though, go for one that’s extra easy to snap together.īTS' Jin Is Ready to 'Start Working Hard Soon' as He Nears the End of His Military Service That can be a little intimidating for listeners who aren’t as savvy with tools, but the good news is that all the ones we tested were simple to put together, usually just with a hammer and screwdriver, but sometimes not needing any tools at all. Even for players that don’t have a connected top, leave some room for whatever kind of covering goes over it to keep the dust and debris away.Īssembly: More than likely, these are going to arrive at your house unassembled. Will you be adding a bigger receiver? More records? Also make sure there’s enough headroom if your record player has a hinged top and needs space to open up. Shelving: Take inventory of what you have, and more importantly, what you’re planning to get in the future as your collection grows.

#Make your own record player shelf how to#

How to Pick the Best Turntable StandĬonsider the below criteria when shopping for the best turntable stand or storage piece. These shelves vary in size, shape, and storage, so here’s what you need to know when finding the right one for you, your space, and your music archive. Worked like a charm.If you purchase an independently reviewed product or service through a link on our website, Rolling Stone may receive an affiliate commission.Įveryone’s collection of records is unique, and having a designated display stand, complete with shelving and a spot for your turntable, is a must for anywhere you listen to music. On my do-over I slid in some long strips of scrap wood and a flat metal square to shield the wood.

It was at this point the first time around that I learned another lesson from the school of hard knocks – protect the plywood! It’s a relatively soft wood, and the clamps leave circular craters if pressed directly into it. So take it from me & my mulligan – don’t get glue on anywhere that you're gonna see later! Step 4: Clamp it togetherĪfter the pieces are assembled and the edges are neatly aligned, the shelf needs to be clamped together while the glue dries. Imagine my deep dismay when I thought I was almost done and then my first coat of stain revealed giant, hideous blotches. It looked so bad I had to start over. That’s actually a lie – the first time I made this shelf I was not careful with the glue cleanup and learned the hard way that Gorilla Wood Glue isn’t stainable. I used a lot of glue to get a really strong hold but I was careful not to get it on ANYTHING that would be visible in the final product. It was basically like making a triple decker mayo sandwich, except simultaneously less delicious & more awesome. I pressed down on the bump-out and wiped up the excess glue that oozed out the sides before applying more glue & securing the top piece. It was important for the thickness of the bump-out wood to match that of the existing shelf so that the 'sandwich buns' on top & bottom would fit snugly and hold the extension in place.

For the bump out, I used a scrap piece of 1 x 10 leftover from our built-ins project, and marked my cuts so it would be 17 inches long and 7.25 inches deep (the difference between the existing shelf and the new shelf). I drew these new measurements on my plywood twice – once for the top piece and once for the bottom. All things considered, my new shelf needed to be 17 inches wide and 16 inches deep (9.25' existing + 4' bump out + 2.75' wiggle room). The width was fine for my ~16 inch wide record player, but I needed at least 4 more inches in depth to fit the base of the player, plus an extra few extra inches to comfortably open and close the dust cover. The space I had to work with was a little more than 17 inches wide and 9.25 inches deep. Step 1: Measure the existing shelf and the record player It’s just 2 pieces of wood slightly bigger than the base of the record player, sandwiched around a third piece of wood that will actually 'bump-out' from the existing shelf. Here’s how I made it. That seems like a lot of supplies, but we had most of them already, and the design is super simple.

Wood stain – test pot of Minwax Honey and test pot of Minwax Special Walnut.1 roll of iron-on wood veneer – 2 in x 8 ft white birch.1 project panel of 1/4 in x 2 ft. x 4 ft sanded plywood.